Electrical Panel Upgrades & Replacement in Brandon, FL

Permits, TECO and Duke Energy, and How the Day Goes

Panel replacements in Hillsborough County, the City of Tampa, Pasco, Pinellas, Polk and Manatee all require an electrical permit and a final inspection. We pull that permit under our license, and we schedule the utility disconnect and reconnect with TECO or, in Pinellas and parts of Pasco, Duke Energy. The utility has to pull the meter so we can work on the service safely, and then re-energize after the inspector signs off or, in jurisdictions that allow it, after we certify the work. Coordinating that sequence is the part homeowners dread, and it is the part we handle for you.

On the day of the upgrade, plan on being without power for roughly four to eight hours. We start early, have the new panel and all materials staged, and work straight through. Keep the refrigerator and freezer closed and they will hold temperature fine. If someone in the home depends on powered medical equipment, tell us when you schedule and we will plan around it, including bringing a temporary generator if needed. When we leave, the old panel, the packaging and the dust leave with us, and you have a labeled panel, a permit record and a written warranty on our workmanship.

What a Panel Upgrade Costs in Tampa Bay

Honest numbers matter, so here they are. A straightforward 200 amp panel replacement in the Tampa area, where the meter base and service entrance are in good shape, generally runs between $2,500 and $5,000 including the panel, breakers, grounding upgrades, surge device, permit and inspection. When the meter base, riser and service entrance cable also need replacing, which is common on homes from the 1960s and 1970s and on anything near the coast, the total usually lands between $4,000 and $7,500. Upgrading from overhead to underground service, relocating the panel, or adding a large subpanel for a workshop or addition moves the number further.

What drives the price is the condition of what we find and the scope you want, not the day of the week or how urgent you sound on the phone. We give you a written price after looking at the service in person, and we explain what each piece is for. If your panel is sound and you really only need a few circuits corrected, we will tell you that too. Many of our panel upgrades are paired with a generator transfer switch or an EV charger circuit because doing them in the same visit saves real money on labor and permits.

Subpanels, Load Calculations and Planning for What Comes Next

A panel upgrade is the right time to think five or ten years ahead, because the cost of adding capacity later is always higher than building it in now. We start every upgrade with an NEC load calculation: the square footage lighting and receptacle load, the kitchen and laundry circuits, the air conditioner, water heater, range, dryer and pool equipment, and any fixed loads like a well pump or a spa. The calculation tells us whether 200 amps is comfortable or whether a large home with two air conditioners, a pool heater and an EV charger is better served by a 320 or 400 amp service. Most Tampa Bay single-family homes land comfortably at 200 amps, and we will tell you honestly if yours does.

Subpanels are the other tool for growth. A detached garage, a workshop, a pool equipment pad, a lanai kitchen or an addition is often best served by its own subpanel fed from the main, which keeps the branch circuits short, puts a disconnect where the load is, and leaves breaker spaces in the main panel free. We size the feeder and the subpanel for the real load and run it in conduit where it is exposed or underground. Homes in Lithia, Plant City and Parrish with barns and workshops use this arrangement constantly, and it is also how we feed pool equipment for pool homes across Brandon and Wesley Chapel.

Inside the panel, a few details separate a careful upgrade from a quick one. Every breaker is sized to its wire, so a 20 amp breaker is never protecting 14 gauge wire. Double-tapped breakers, where two circuits share one breaker terminal, are corrected with proper tandem breakers or new circuits. The neutral and ground bars are separated as required, each conductor gets its own terminal, and everything is torqued to the manufacturer's specification with a calibrated torque screwdriver, which is a code requirement most homeowners have never heard of and most inspectors now check. We leave a typed panel directory, photograph the finished work, and walk you through it before we close the cover.

Talk to a Licensed Tampa Bay Electrician About Your Panel

Whether your insurer sent a letter, your breakers are tripping, or you are planning a generator, EV charger or pool and want to know if your service can handle it, start with a conversation. Lightning Bay Electric serves all of Tampa Bay, and you can check your neighborhood on our service areas page. Read what homeowners say about working with us on our reviews page, then call (813) 897-2665 or send a photo of your panel through our contact form for a fast, no-pressure assessment.